how to change a front wheel bearings

Step 1 . WHEEL BEARING REPLACEMENT: GETTING STARTED

These instructions apply to bearings in a non-drive wheel. In other words, if your car is front wheel drive, we're talking about the rear bearings. If it's rear wheel drive, you'll be replacing the front wheel bearings.

How do I know if I need new wheel bearings? Most of the time we don't even know that they need service. We just drive and never think about them. Most car manufacturers recommend a wheel bearing clean, inspection and repack every 30,000 miles. This is usually done along with the front brake service. They need to be replaced when there is scoring and pitting or they become noisy.

What you'll need:

1. Large adjustable wrench and Channelocks
2. Bearing race driver tool or various size punches
3. Socket and ratchet set or assorted wrenches
4. BFH
5. Lots of rags
6. New wheel bearings
7. Wheel bearing grease
8. New cotter pin
9. New grease seals
10. Wheel blocks
11. Safety glasses
12. A jack and a pair of jack stands
13. Rubber gloves (Optional)

Make sure that your car is parked on a level grade, rather than on any sort of hill or inclined driveway. Jack up the car and place your jack stands under the frame to support the vehicle. Block the rear wheels to prevent rolling. Set the parking brake and if you have an automatic transmission, put in Park.

Step 2. WHEEL BEARING REPLACEMENT: REMOVING THE OLD WHEEL BEARING

In most cases, you will need to remove your disc brake calipers and caliper bridge to remove the rotor. See Replacing Your Disc Brake Pads for more information on this. If your car has drum brakes, ignore this step.

• First, remove the bearing cap. This is a press fit and to remove it grab it with your Channelocks and work it back and forth until it pops off. Be careful not to crush it as you remove it.
• Once the cap is off you will see a cotter pin, Remove the cotter pin and remove the retainer ring. If your vehicle has a castellated nut, you will not have a retaining ring.
• Using your Channelocks or adjustable wrench, remove the nut from the spindle.
• Now remove the outer wheel bearing and washer and lay it aside.
• Slide the rotor or drum off the spindle. This may be difficult, but it will come off. Don't worry about hurting the grease seal; we're going to replace it anyway.
• Now that the rotor or drum is off, use a suitable tool to remove the grease seal and take out the inner wheel bearing.
• Using some of the rags wipe all the old grease from inside the hub.
• Now we need to remove the bearing races from the hub. Take a punch with a flat narrow tip and place it on the back of the race. Most hubs have gaps in them to expose the back of the race to make removal easier. Tap the race out, alternating from side to side so it comes out evenly and doesn't get cocked in the hub. Once it's out, flip the rotor or drum over and do the same for the other race.

When both races are out, clean the inside of the hub with some rags. Also make sure the spindle is clean as well. You can even use some carburetor cleaner to do a really good job of cleaning. From this point on cleanliness is important. You do not want any dirt, sand or metal chips inside the hub.

Step 3. WHEEL BEARING REPLACEMENT: GREASING IT ALL

Now that everything is nice and clean, let's put the new races and bearings in.

• Take one of the new races and coat the outside with some wheel bearing grease. This will help it slide into the hub. If you have a race driver, select the proper size and tap the new race into the hub. Make sure you drive it in evenly and do not cock it. If you don't have a race driver, use your hammer to tap the outside of the race to get it started making sure you tap evenly around the race. When it is flush with the hub, use your flat narrow punch and drive it in the rest of the way. Make sure it is fully seated. The sound of the tapping will change when it's seated and you can look from the other side to visually confirm this.
• Do the same for the other race.
• If you don't have a bearing packer, you will need to pack them by hand. Put a glob of wheel bearing grease in the palm of your hand. Slip the wheel bearing on your index finger like a ring with the wide end facing out. Then tap the bearing into the glob of grease until you see it coming out the other side. When you see it come out turn the whole bearing, don't just rotate it on your finger, and repeat the procedure until the whole bearing has grease coming out the other side. Repeat this for the other bearings.

Step 4. WHEEL BEARING REPLACEMENT: REASSEMBLY

1. Now that we have the races installed and bearings packed, we can put everything back together. Starting with the inner bearing put a bed of grease on the surface of the race and then push the inner wheel bearing into it. Take the new grease seal and tap it into place, don't bend or distort it. You can use a small block of wood to help.
2. Put a coating of grease inside the hub between the two races and on the spindle -- too much is better than too little. If any moisture should happen to get inside, the grease will keep the metal from rusting.
3. Slide the brake rotor or drum straight onto the spindle. It should slide on easily. If it doesn't, the bearing is cocked a little. Slide it off and make sure the bearing is sitting flat and try again.
4. Once it's on, grease the outer race and slide the outer wheel bearing on. Slide the washer on. The washer will probably have a tab that will align with the spindle, make sure that you line them up when you put it in.
5. Place the nut on the spindle and tighten it by hand until it won't go anymore. Spin the rotor or drum a few times back and forth and then tighten the nut more by hand. This insures that the bearings are seated. Do it a couple of times until you can't get it any tighter by hand.
6. Now tighten the nut ¼ turn, no more than 16 foot-pounds. If you have a castellated nut, line it up with the hole going through the spindle. Install a NEW cotter pin. If you have a retaining ring, place it on the nut and install the pin. Never reuse the old cotter pin and make sure you use it.
7. Put a small blob of grease on the inside of the dust cap and tap it into place, being careful not to crush it. Make sure it is fully seated.
8. That's it, you're ready to roll nice and smooth!